INSTALLATION OF THE SELF ADHESIVE FILM

智能调光玻璃

2020/04/02 发布于 科学 分类

智能调光玻璃自贴膜安装教程。

智能调光膜,  自贴膜  调光膜  玻璃  PDLC膜 

文字内容
1. GUANGZHOU HUICHI INDUSTRIAL DEVELOPMENT CO., LTD Add: Likang Industrial zone, tancun, shitan road, shijing, baiyun district, 510430, Guangzhou, CHINA. TEL: +8618922173106 E-MAIL: mukial@huichiglass.com INSTALLATION OF THE SELF-ADHESIVE FILM Installation of self-adhesive film REMARK: Due the package of the film is rolling, if you stick it on the glass directly , it is not easy to do it, we suggest you can put it on the clean table for 1 hour and then stick it on the glass. Before installation,, we suggest to connect with the transformer to test first, to check if the film can work normally,especially on the edge and 4 corners. 1) Confirm the size if correct: Check the width and height(if the size is bigger, then you can use the scissors or knife to cut it smaller, but cannot cut the side with bus bar. 2) Clean the surface of the glass: use the soap water to clean the dust which is on the glass, and then use the clean water(alcohol) to clean it again. Please note that the film can not stick with water, before you apply the film on the glass, please be sure that there is no water on the glass, the surface should be dry!!! 3) Installation: There are 3 layers of the self-adhesive film: first layer is the protection film for the glue side(noted 1), and the protection film for the smart film(noted Please be careful when you take out the protect film for 1 and 3, you cannot seperate 4,5 and 6. 4) Installation step: 4.1 From up to down for positioning, the 2 corners on the top should fit with the glass. 4.2 After positioning, take out the protect film on the glue side for ab out 30cm,and apply it on the glass for fixing, if there is bubble on this step, ignore it. 4.3 You can stick it on the glass and take out the protect film(on glue side) at the same time, if you find the bubble, use the tools to push it out. After installed all pcs the film, and then you can deal with the bubble which appear on the 30cm area, take out the adhesive film on 30cm area, from down to up to push the bubble out. After installation, you can connect the wire to the bus bar(copper net), and then the test
2. GUANGZHOU HUICHI INDUSTRIAL DEVELOPMENT CO., LTD Add: Likang Industrial zone, tancun, shitan road, shijing, baiyun district, 510430, Guangzhou, CHINA. TEL: +8618922173106 E-MAIL: mukial@huichiglass.com again. When you finish all the installation, please take out the protect film(no.3). By the way, you can use the silicone for the sealing of the film to protect the smart film, please note that the glue should be fast drying and neutral. You can ask the supplier for a recommendation!!! ACID ONE IS FORBIDDEN, PLEASE TEST IT BEFORE YOU USE THE SILICONE!!! FOLLOWING IS THE INFORMATION NEED TO NOTE WHEN YOU APPLY THE FILM. 1) You don’t have to use other material for the adhesion, there is glue on the PDLC film. 2) Please don’t fold it and make the shape changed, or it is hard to install it or lead to the film damaged. 3) Please be sure that the glass should be clean totally and no water or dust on the glass, or it will lead to the bubble. 4) You can not use the shark knife or other material to scratch the film. 5) The film cannot use 110V or 220VAC OR DC directly, you must connect with the transformer to convert the voltage, normally it is 60VAC. Please ask your supplier for a recommendation if you are not clear!!!